The king cobra is a cobra bracelet woven twice: a standard cobra base, then a second cobra layer worked right over the top of it. The result is a wider, heavier bracelet that carries roughly twice the cord of a regular cobra — and that is exactly where beginners go wrong. If you cut cord using standard cobra numbers, you will run out about halfway through the second layer. This tutorial gives you the exact cut lengths first, then walks through the build one knot at a time.
You only need to know one knot for the whole project. If you can tie a cobra (Solomon bar), you can tie a king cobra. The second layer is the same knot, tied over a fatter core.
What You Need
- 550 paracord, Type III — one color, or two colors for a contrasting top layer
- 5/8-inch contoured side-release buckle
- Sharp scissors
- Lighter (for melting ends)
- Tape measure or ruler
- Optional: a bracelet jig, which holds tension and makes the whole job easier
No specialty tools are required. A jig helps, but a clipboard or your own knee works fine for holding the buckle end steady.
Sizing: Measure Your Wrist, Then Add Room
A king cobra bracelet is thick — close to 3/8 inch — and it sits proud of the wrist. Size it like a standard bracelet and it will fit like a tourniquet.
- Wrap a tape measure (or a strip of paper) around your wrist where the bracelet will sit. Note the snug measurement.
- Add 1 to 1.5 inches. That total is your finished length, measured buckle-to-buckle on the completed bracelet.
- If the bracelet is a gift and you cannot measure, an 8-inch finished length fits most adult wrists.
The Cord Math
A king cobra uses about 24 inches of cord for every finished inch of bracelet: roughly 12 inches per inch for the cobra base, and another 12 inches per inch for the king layer over it. That rate includes your working ends.
| Your wrist | Finished length | Total cord to cut |
|---|---|---|
| 6.5 in | 7.5 in | 15 ft |
| 7 in | 8 in | 16 ft |
| 7.5 in | 8.5 in | 17 ft |
| 8 in | 9 in | 18 ft |
| 8.5 in | 9.5 in | 19 ft |
For a two-color bracelet, cut the total in half: an 8-inch finished bracelet takes about 8 ft of the base color and 8 ft of the top-layer color. When in doubt, cut long. You can trim cord at the end; you cannot add it mid-weave. For any other size or weave, run your numbers through the paracord length calculator — and if you want the math behind these rates, see how much paracord do I need?
Part 1: Build the Cobra Base
If you have never tied the base weave at all, work through our cobra bracelet tutorial with a buckle first, then come back here for the second layer.
- Fold your base cord (or the full length, if you are using one color) in half. Push the loop through one half of the buckle and pull the ends through the loop to form a cow hitch. You now have two core strands hanging from the buckle.
- Thread the two core strands through the other buckle half so the buckle-to-buckle distance equals your finished length. Secure the second end the same way. These two taut strands are your core — every knot wraps around them.
- Take the left working strand and cross it over the core. Take the right working strand, lay it over the left strand’s tail, then pass it under the core and up through the loop on the left side. Pull snug.
- Repeat on the other side: right strand over the core, left strand over its tail, under the core, and up through the right loop. Pull snug.
- Keep alternating sides. Each pair of knots makes one flat “bar.” Push each new bar up against the last one and keep tension even.
- Continue until the weave reaches the far buckle. That is your cobra base — it should look like a neat row of interlocking Vs.
Part 2: Weave the King Layer
The king layer is tied directly over the base, using the finished bracelet itself as the core.
- Take your second cut of cord (the top-layer color, or the remaining half of a single-color cut). Anchor it at the buckle end: pass the midpoint behind the bracelet just below the buckle and pull the two working ends out to the sides so the cord locks in place.
- Tie the first cobra knot around the whole base bracelet, not just the two core strands: left strand over, right strand over its tail, under the bracelet, up through the loop. Pull down firmly — this knot needs more tension than the base knots did.
- Alternate sides, exactly as you did for the base. Each knot should sit in the “valley” between two base bars and squeeze the base slightly.
- Work your way to the far buckle, keeping the rows straight. If a knot lands crooked, back it out and re-tie it now — the king layer hides nothing.
- At the far buckle, tie two extra knots in the same spot to lock the layer down before finishing.
Finishing: Trim and Melt the Ends
- On the underside of the bracelet, trim each working end to about 1/4 inch.
- Hold the lighter flame just off the cut end until the nylon melts into a small mushroom cap, then press it flat against the underside of the weave with the side of the lighter or a thumb guard. The melted cap is what stops the knot from ever pulling loose.
- Do the same for the base-layer ends if any are still exposed.
- Test the bracelet: flex it, pull the buckle ends apart firmly, and check that no melted end sits where it will rub your wrist. A sharp melted edge can be re-melted and pressed smoother.
Troubleshooting
The bracelet twists like a barber pole. You tied every knot starting from the same side. The cobra only stays flat if you strictly alternate: left-over, then right-over. Untie back to where the twist starts and resume alternating.
Bars are lumpy and uneven. Your tension changes from knot to knot. Pull each knot to the same snugness, and slide each new bar up tight against the previous one before tying the next.
The king layer slides around. The base was too loose, or the king knots are not tight enough. The top layer should visibly compress the base. Cinch each knot harder, especially the first three.
I ran out of cord. You cut by cobra numbers instead of king cobra numbers, or your finished length grew while weaving (loose knots eat length). Next time, use the table above. A splice mid-layer always shows — on a bracelet, starting over is usually cleaner.
The finished bracelet is too tight. The buckle-to-buckle distance was set to your raw wrist measurement. Rebuild with the full 1 to 1.5 inches of allowance; thickness is part of the fit.
FAQ
How much usable cord does a king cobra bracelet hold?
An 8-inch finished king cobra holds about 16 ft of cord total, including the core strands. Unraveled, that is enough for shelter lashing, a tourniquet substitute in a pinch, gear repair, or a fishing line core strand — the whole point of carrying cord on your wrist.
Is the king cobra harder than a regular cobra?
No — it is the same single knot, tied twice. The only real differences are planning the extra cord, setting a longer finished length, and pulling the second layer tighter. If your plain cobra comes out neat, your king cobra will too.
Can I make a king cobra without a buckle?
Yes. Replace the buckle with a loop-and-knot closure (a diamond knot through a fixed loop) or weave it around a core measured straight to length. The cord math is identical; only the hardware changes.

